Standard specification of high-precision filter (β3≥929)

Remove contaminants that cannot be removed by general filters

Remarks: Maximum flow rate: As the viscosity increases, the mechanical pressure will increase and the discharge volume will decrease.

OCS stand-alone standard oil filter is designed with a variety of structures, and optional components include preheater, drip pan, casters, pre-filter device, etc. It can also provide you with actual use schemes and non-standard production according to the different needs of the user's purpose, use conditions, oil types, oil viscosity, and precision requirements.

Innovate the F180001 filter element to the WG180001 filter element. The OCS oil filter is used for the filtration of water-based hydraulic fluid: WG type water glycol filter element, non-woven fabric is embedded in the filter element drum, the bottom layer is covered with a thin non-woven fabric, and the outside is added Pressed epoxy resin pipe, after special anti-corrosion treatment, only removes impurities, not water, and is dedicated to water glycol.

Remarks: For the technical parameters and performance characteristics of the water glycol oil purifier, please refer to the P4 technical parameters.

OCS stand-alone standard configuration filter element (PF front stage filter element, F type precision filter element)

It is made of filtered cellulose by rolling and pressing. When the polluted oil passes through the surface of the filter element, the large particles are isolated, and then continue to flow into the upper layer of the low-density filter element to filter the remaining large particles, but the fine particles can still pass through, so as to avoid The upper layer is blocked, and the tapered pores of the filter element uniformly distribute the particles in the fiber, thereby increasing the dirt holding capacity of the filter element. Finally, the lower layer of the high-density filter element captures micron-sized particles.

F-type precision filter element: deep-wound thin-structure high-performance filter element, strong water absorption, high filtration accuracy, suitable for hydraulic oil, lubricating oil, turbine oil, etc. Model: F180001

PF type high-pollution filter element: The front-stage filter element is made of a multi-layer stainless steel filter screen through a special laminate and vacuum sintering. It has high strength and overall rigidity, and has the characteristics of repeated cleaning. Model: PF10080

The ultra-precision filter is a fine filter used for off-line filtration or on-line bypass circulating filtration, which can clean and filter liquids in medium and large hydraulic transmission systems, lubrication systems, and cooling systems.

The ultra-precision filter is equipped with a long-path filter with an absolute accuracy of 3 microns (meaning that 98.7% of solid particles larger than 3 microns and about 50% of solid particles larger than 0.8 microns can be blocked in one filtration), which has a very The high dirt holding capacity and fiber-based filter element are used to remove particulate matter, absorb oil degradation products (oxide, resin/sludge, varnish), and absorb emulsified water and free water of oil.

The ultra-precision filter is designed by a variety of mechanisms, and the optional components include preheater, drip pan, casters, pre-filter device, etc. It can also provide customers with actual use schemes and non-standard production according to different needs of users, such as users' purposes, use conditions, oil types, oil viscosity, and precision requirements.

Matching filter element introduction: F180001 filter element

It is made of filtered cellulose by rolling and pressing. When the polluted oil passes through the surface of the filter element, the large particles are isolated, and then continue to flow into the upper layer of the low-density filter element to filter the remaining large particles, but the fine particles can still pass through. The upper layer of the filter element is blocked, and the conical pores of the filter element make the particles evenly distributed in the fiber, thereby increasing the dirt holding capacity of the filter element. Finally, the lower layer of the high-density filter element captures micron-sized particles.

F-type ultra-precision filter element: a high-performance filter element with deep, thin crepe structure, strong adsorption and hydrophilicity, high filtration accuracy, suitable for hydraulic oil, lubricating oil, turbine oil, insulating oil, etc.

Reminder: Replacement cycle of filter element

1. The replacement cycle of the filter element varies greatly according to the amount of filtration or the degree of pollution of the oil used.

2. When particles, metal powders, and other pollutants are mixed in the pollutant, the filter element has a long life, but if it is mixed with water, the exchange cycle of the filter element is faster.

3. The replacement cycle of the filter element is when the needle of the pressure gauge exceeds the set value, it will prompt to be replaced. This is because the absorption capacity of the filter element increases and the pressure rises. If the needle of the pressure gauge is more obvious than the normal setting value or points to zero, the filter element will absorb water and crack in the filter element, so you can update it in time.